Mean Well Power Supply, NES-75-12

Original Mean Well Power Supply, NES-75-12,85~264V AC universal input, output:12V DC,0~6.2A, 74.4W

Original Mean Well Power Supply, NES-75-12,85~264V AC universal input, output:12V DC,0~6.2A, 74.4W

 Specifications:

NES-75-12

1. Output:

1)  DC Voltage: DC12V

2)  Rated currrent: 6.2A

3)  Current range: 0~6.2A

4)  Raged power: 74.4W

5)  RIPPLE & NOISE (max.) Note.2: 120mVp-p

6) VOLTAGE ADJ. RANGE: 10.8 ~ 13.2V

7)  VOLTAGE TOLERANCE Note.3: ±1%

8) VOLTAGE TOLERANCE Note.3: ±0.5%

9) LOAD REGULATION Note.5: ±0.5%

10) SETUP, RISE TIME:500ms, 30ms/230VAC 

11)  HOLD UP TIME (Typ.):50ms/230VAC

2. Input:

1) VOLTAGE RANGE:85 ~ 264VAC   

2) FREQUENCY RANGE:47 ~ 63Hz

3) EFFICIENCY (Typ.):82%

4) AC CURRENT (Typ.):  0.9A/230VAC

5) INRUSH CURRENT (Typ.): COLD START 45A

6) LEAKAGE CURRENT: <2mA / 240VAC

7) LEAKAGE CURRENT<2mA / 240VAC

3. Protection:

1) OVERLOAD 110 ~ 150% rated output power

Protection type : Hiccup mode, recovers automatically after fault condition is removed

 2) OVER VOLTAGE:

13.8 ~ 16.2V

Protection type : Shut down o/p voltage, re-power on to recover

4. SAFETY & EMC (Note 6)

1) SAFETY STANDARDS: UL60950-1, CB(IEC60950-1),CCC GB4943 approved

2) WITHSTAND VOLTAGE:I/P-O/P:3KVAC     I/P-FG:1.5KVAC     O/P-FG:0.5KVAC

3) ISOLATION RESISTANCE: I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 °C/ 70% RH

4) EMC EMISSION: Compliance to  EN55022 (CISPR22) Class B, EN61000-3-2,-3

5) EMC IMMUNITY:Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-1, light industry level, criteria A

5. Others

1) MTBF: 378.2K hrs min.      MIL-HDBK-217F (25°C)

2) DIMENSION: 159*97*38mm (L*W*H)

3) PACKING:0.52Kg; 30pcs/16.6Kg/0.97CUFT

6. Notes:

1) All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.2)  Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.3) Tolerance : includes set up tolerance, line regulation and load regulation.4) Line regulation is measured from low line to high line at rated load.5) Load regulation is measured from 0% to 100% rated load.6) The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meetsEMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”(as available on http://www.meanwell.com)

Mean Well Power Supply, NES-75-12